You are nearly there, we just need to confirm your email address.
To complete the subscription process please click the link in the email we just sent you. If you did not receive the email please check your spam folder or contact us at firstname.lastname@example.org.
Submit your email to receive the latest expert blogs, industry insights, Neles' customer stories, whitepapers, webinars and Q&As directly to your email.
Jul 21, 2020
For loop tuning, do you need a bump test?
Head of Performance Solutions
The short answer to the original question is: Yes, you do need a bump test. However, the bump test does not need to be a traditional one.
Controller Tuning is basically the act of matching the controller’s response to the process. To be more specific, it is figuring out exactly how to move the controller output (valve) in response to disturbances. As a secondary motivation, we also want the controller to respond appropriately to set point changes…not too fast, not too slow.
To tune the controller properly, you must have a good, mathematical answer to this question: How will the process respond when I move the controller output?
In other words, you need a model of the process response to the valve position. From this model, you can develop appropriate tuning. There are many “tuning rules” that have been developed over the years, to select appropriate tuning, once you have a good process model. The Expertune PlantTriage proprietary tuning rules have been carefully selected over many decades of process experience, and represent a balance between fast performance and process robustness.
Can I develop a good response model without a bump test?
Certainly the simplest approach is to use a traditional “bump test”. Put the loop in manual, and make a step change to the controller output. The process responds, and you can easily measure the response, calculate the process model, and then apply tuning rules. But bump tests can be problematic: operators are resistant to putting loops in manual, the bump test is an upset to the process, so it can have quality, environmental, or safety impact. And it can take quite some time before the process stabilizes, especially if it is a thermal process. For example, bumping a distillation column might take 12 to 24 hours for a full response.
An alternate type of bump test is a setpoint change. Like the manual bump test, the control output moves, and the process moves in response.
Other types of intentional movement of the Control Output can also be used: pulse tests, doublet pulses, ramps, and pseudo-random changes to control output or setpoint may give enough process excitation to deliver a good model. These techniques can be very useful in reducing the time required in large, slow processes, like we typically find in chemical plants and oil refineries.
Expertune PlantTriage’s Active Model Capture Technology (AMCT) will automatically find process models when output changes, setpoint changes, or other suitable sequences occur. This greatly reduces the work needed to develop models. You can simply ask the operator to make some setpoint changes, and PlantTriage will automatically find models.
Disturbances, however, are NOT useful for process modelling. In the case of an upset, or disturbance, a loop in automatic will move the controller output in response to the upset. But here is the problem: You don’t know how much process response comes from the disturbance, and how much comes from the control response.
So, the short answer to the original question is: Yes, you do need a bump test. However, the bump test does not need to be a traditional bump test. And Expertune PlantTriage’s AMCT can greatly speed up the modelling work by finding and determining models (and tuning!) based on normal operator actions.
In a typical plant, many controls and processes are not operating optimally, which can result in less stable production, higher raw material usage, increased energy consumption and lower yield. Neles™ PID tuning and process control services are designed to identify controls impacting performance and help you return to optimal production.
Expertune PlantTriage is an award-winning PID tuning software, developed by a team with hundreds of years of controls experience. It continually monitors your plant to identify issues whenever they occur. Expertune PlantTriage prioritizes the information based on technical and economic factors, helps to find the root cause of issues, and provides a complete set of analysis tools to resolve the problem at its cause.
In many plants, process engineers are guessing PID tuning numbers. The outcome of guesswork is increased wear on valves, shortened valve life, poor control, and inconsistent results. Expertune PID Loop Optimizer is a PID tuning software designed to eliminate the guesswork. It helps in properly tuning and stabilizing the plant, improves the reliability of valves, and makes it easier to sleep at night.